|
SPECIFICATIONS |
SL-1100 | |
RACK DIMENSIONS |
500 x 500 mm | |
No.OF RACKS |
2 | |
Maximum Dish / Pan Height |
400 mm | |
CYCLE |
120 sec | |
OUTPUT : racks / hr |
30 | |
DRAIN PUMP |
NO | |
Automatic Detergent Injection |
YES | |
ELECTRICAL SUPPLY |
240V / 50Hz / 1-400V / 50Hz / 3N - | |
ELECTRICAL LOADING |
||
Wash Pump |
880 W / 1.2 Hp | |
Wash Tank |
2.500 W | |
Rinse Tank |
6.000 W | |
Total Power |
9.380 W | |
TEMPERATURE |
||
Washing (°C ) |
55°C - 65°C | |
Rinsing (°C ) |
85°C - 90°C | |
WATER CAPACITY |
||
Wash Tank |
40 L | |
Rinse Tank |
10 L | |
Water supply pressure |
2-4 / 200-400 | |
WATER USAGE PER CYCLE |
3.5 L | |
EXTERNAL DIMENSIONS |
||
-Width |
640 mm | |
-Depth |
756 mm | |
-Height (open/closed) |
1.920 / 1.468 mm | |
COMPLETE WITH |
1 open rack 1 plate rack | |
| 1 cutlery basket | ||
NET WEIGHT |
104 Kg |
SL-1200
PASS THROUGH DISHWASHER
SPECIFICATIONS |
SL-1200 | |
RACK DIMENSIONS |
500 x 500 mm | |
No.OF RACKS |
2 | |
Maximum Dish / Pan Height |
400 mm | |
CYCLE |
60 / 120 sec | |
OUTPUT : racks / hr |
60 / 30 | |
DRAIN PUMP |
NO | |
Automatic Detergent Injection |
YES | |
ELECTRICAL SUPPLY |
240V / 50Hz / 1-400V / 50Hz / 3N - | |
ELECTRICAL LOADING |
||
Wash Pump |
1.500 W / 2 Hp | |
Wash Tank |
3.000 W | |
Rinse Tank |
9.000 W | |
Total Power |
13.50 W | |
TEMPERATURE |
||
Washing (°C ) |
55°C - 65°C | |
Rinsing (°C ) |
85°C - 90°C | |
WATER CAPACITY |
||
Wash Tank |
40 L | |
Rinse Tank |
12 L | |
Water supply pressure |
2-4 / 200 - 400 | |
WATER USAGE PER CYCLE |
3.5 L | |
EXTERNAL DIMENSIONS |
||
-Width |
640 mm | |
-Depth |
756 mm | |
-Height (open/closed) |
1.920 / 1.468 mm | |
COMPLETE WITH |
1 open rack 1 plate rack | |
| 1 cutlery basket | ||
NET WEIGHT |
112 Kg | |
.These machines have been designed and manufactured in accordance with the specifications laid down in European directives 89/392/ EEC and 73.23/ EEC . Please note : that as a result of continuous product improvements , these specifications are subject to change without prior notice |
| INSTALLATION |
Machines to be installed by suitably qualified personnel
and in accordance with local ordinances , codes and standards,
install the machines on a self draining floor. |
| WATER SUPPLY | Connect the machine to the hot water outlet , in coming water to be greater than 60°C and lesser than 70°C |
| WATER PRESSURE | Being supplied to the machine is not less than ( 200 Kpa ) and no greater than 4 bar ( 400 kPa ) |
| LOW WATER PRESSURE | A booster pump is required for low water pressure to the machine |
| HARD WATER | In hard water areas a water softener is recommended especially for glasswashers |
| POWER | Check that the voltage of the machine coincides with the mains voltage , electrical supply 240 / 50Hz / 1 - 400 / 50Hz / 3N - |
| COMMISSIONING | Enshore that the machine has been installed as per instructions, and that the drain plugs are in place. Turn on the water first , then then switch on the main power switch , close the door , engage the start button on the machine , the machine will begin to fill , the rinse tank will fill first , then the wash tank, these procedures may take some minutes to complete , when the ready light comes on the machine will ready to operate |
 |
Head Office: All initial mail correspondence to Head Office please * * * * * * * * * Regional Office Addresses: NSW QLD VIC |